Firmware 2.06 finally out

[Alias1]

Memory Card and ftp update is available
(Internet update is no available this time)

* How to update TGS100 with Memory Card automatically.
1. Copy all files only inside folder(after de-compression) to the memory card.
http://itgate.co.kr/Rel/206/TGS100automc_rel206.zip
2. Switch off TGS 100 and insert the memory card into the memory card slot of front panel.
3. Switch on TGS 100 and you can see "doun" on LED display, it means downloading is started.
4. Soon after, you can see downloading process by number(1~100) on LED display. Please wait until it shows "done"
5. After checking "done" on LED display, remove Memory Card and switch off and on again.
6. Downloading completed!
Warning) Do not remove memory card during reading and writing mermory card in any cases.

*How to update TGS100 with ftp.
1) Down load S/W
http://itgate.co.kr/Rel/206/TGS100ftpmc_rel206.zip
Down load the zip file and unzip, Check "install.tar" file inside

2) Connecting ftp
Setup Menu -> Expert Setup -> Communication Setup -> Check your IP in the box
and connect the IP (ex "ftp://192.168.1.xxx" )
Put ID & Password as below
login : root
Password : itgate

3)ftp Upload
Move to "/var/etc"
Copy the "install.tar" to "/var/etc"

4)Reset
Turn off & on, After booting s/w upload starting
After donloading finish, show you "done" message.
Turn off & on again
Downloading complete
Remark) The boothing time will take in a minute

Improvements are :

- No more CI initialization error
- 16:9 bug fixed
- Volume range bug fixed
- DiSEqC motor move bug fixed
- PVR Trick Play bug fixed
- Pressing and hold FF or REW to input to move wished position
- Busybox Upgraded to 1.01
- Minimized HDD sleep mode duration
- Record indication ; Blinking red power LED with blinking REC on display
- Timer bug fixed

[Alias1]

I must be just plain stupid cause I cant get either of the above two methods to load on my box
So I renamed to no_boot and loaded it on SD card
Comes up unknow version on firmware also still problems with lipsync and slow on channel change.
Glad I waited 3 months for this rofl

[pat911]

I've got it loaded but the W/S problem isn't totally fixed, although it is better. 16:9 programs are now OK but 4:3 programs are being automatically stretched. What is missing is the "16:9 (Always)" option that is available on the dreambox.

Cheers
Pat.

[Far_Call]

Tried both methods and working fine with clean installs.

Still some lipsync issues but will test and see what other issues it has.
Apart from that its looking pretty good.

[Far_Call]

Is this version compatable with ITGate 200 ?

[Alias1]

Originally Posted by Far_Call

Tried both methods and working fine with clean installs.

Still some lipsync issues but will test and see what other issues it has.
Apart from that its looking pretty good.

I had to serial flash back to 2.03 then use the ftp method to get it in flash.
These boxes still have a long way to go to catch up to a dream
Still have SLIGHT lipsync problems and slow channel change to get picture.

[pat911]

Originally Posted by Alias1

I had to serial flash back to 2.03 then use the ftp method to get it in flash.

Same here. I had to serial back to 2.0.5 then I used SD card method. I had DSTeam loaded previously. Maybe that has domething to do with it.

Cheers
Pat

[zephyr]

I wonder when 2.0.7 comes out. The old forum itgateusers dissapeared and restarted with a new board. So now it's quite tough to get in touch with the dev's.